| Age | Commit message (Collapse) | Author | Lines |
|---|
|
Loongson 3A4000 is a MIPS-based Loongson64 CPU which also supports
8250_loongson (loongson-uart).
Enable building on MIPS Loongson64 so that Loongson 3A4000 can benefit
from it.
Signed-off-by: Rong Zhang <rongrong@oss.cipunited.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://patch.msgid.link/20260315184301.412844-3-rongrong@oss.cipunited.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The F81214E is a LPC/eSPI to 2 UART Super I/O chip.
Functionally, it is the same as the F81216E. The only difference
is that the F81216E has 4 UART ports, whereas the F81214E has 2
UART ports.
Signed-off-by: Ravi Rama <ravi.rama@nexthop.ai>
Link: https://patch.msgid.link/20260313194731.2671-1-ravi.rama@nexthop.ai
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DW UART cannot write to LCR, DLL, and DLH while BUSY is asserted.
Existance of BUSY depends on uart_16550_compatible, if UART HW is
configured with it those registers can always be written.
There currently is dw8250_force_idle() which attempts to achieve
non-BUSY state by disabling FIFO, however, the solution is unreliable
when Rx keeps getting more and more characters.
Create a sequence of operations that ensures UART cannot keep BUSY
asserted indefinitely. The new sequence relies on enabling loopback mode
temporarily to prevent incoming Rx characters keeping UART BUSY.
Ensure no Tx in ongoing while the UART is switches into the loopback
mode (requires exporting serial8250_fifo_wait_for_lsr_thre() and adding
DMA Tx pause/resume functions).
According to tests performed by Adriana Nicolae <adriana@arista.com>,
simply disabling FIFO or clearing FIFOs only once does not always
ensure BUSY is deasserted but up to two tries may be needed. This could
be related to ongoing Rx of a character (a guess, not known for sure).
Therefore, retry FIFO clearing a few times (retry limit 4 is arbitrary
number but using, e.g., p->fifosize seems overly large). Tests
performed by others did not exhibit similar challenge but it does not
seem harmful to leave the FIFO clearing loop in place for all DW UARTs
with BUSY functionality.
Use the new dw8250_idle_enter/exit() to do divisor writes and LCR
writes. In case of plain LCR writes, opportunistically try to update
LCR first and only invoke dw8250_idle_enter() if the write did not
succeed (it has been observed that in practice most LCR writes do
succeed without complications).
This issue was first reported by qianfan Zhao who put lots of debugging
effort into understanding the solution space.
Fixes: c49436b657d0 ("serial: 8250_dw: Improve unwritable LCR workaround")
Fixes: 7d4008ebb1c9 ("tty: add a DesignWare 8250 driver")
Cc: stable <stable@kernel.org>
Reported-by: qianfan Zhao <qianfanguijin@163.com>
Link: https://lore.kernel.org/linux-serial/289bb78a-7509-1c5c-2923-a04ed3b6487d@163.com/
Reported-by: Adriana Nicolae <adriana@arista.com>
Link: https://lore.kernel.org/linux-serial/20250819182322.3451959-1-adriana@arista.com/
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When DW UART is !uart_16550_compatible, it can indicate BUSY at any
point (when under constant Rx pressure) unless a complex sequence of
steps is performed. Any LCR write can run a foul with the condition
that prevents writing LCR while the UART is BUSY, which triggers
BUSY_DETECT interrupt that seems unmaskable using IER bits.
Normal flow is that dw8250_handle_irq() handles BUSY_DETECT condition
by reading USR register. This BUSY feature, however, breaks the
assumptions made in serial8250_do_shutdown(), which runs
synchronize_irq() after clearing IER and assumes no interrupts can
occur after that point but then proceeds to update LCR, which on DW
UART can trigger an interrupt.
If serial8250_do_shutdown() releases the interrupt handler before the
handler has run and processed the BUSY_DETECT condition by read the USR
register, the IRQ is not deasserted resulting in interrupt storm that
triggers "irq x: nobody cared" warning leading to disabling the IRQ.
Add late synchronize_irq() into serial8250_do_shutdown() to ensure
BUSY_DETECT from DW UART is handled before port's interrupt handler is
released. Alternative would be to add DW UART specific shutdown
function but it would mostly duplicate the generic code and the extra
synchronize_irq() seems pretty harmless in serial8250_do_shutdown().
Fixes: 7d4008ebb1c9 ("tty: add a DesignWare 8250 driver")
Cc: stable <stable@kernel.org>
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
INTC10EE UART can end up into an interrupt storm where it reports
IIR_NO_INT (0x1). If the storm happens during active UART operation, it
is promptly stopped by IIR value change due to Rx or Tx events.
However, when there is no activity, either due to idle serial line or
due to specific circumstances such as during shutdown that writes
IER=0, there is nothing to stop the storm.
During shutdown the storm is particularly problematic because
serial8250_do_shutdown() calls synchronize_irq() that will hang in
waiting for the storm to finish which never happens.
This problem can also result in triggering a warning:
irq 45: nobody cared (try booting with the "irqpoll" option)
[...snip...]
handlers:
serial8250_interrupt
Disabling IRQ #45
Normal means to reset interrupt status by reading LSR, MSR, USR, or RX
register do not result in the UART deasserting the IRQ.
Add a quirk to INTC10EE UARTs to enable Tx interrupts if UART's Tx is
currently empty and inactive. Rework IIR_NO_INT to keep track of the
number of consecutive IIR_NO_INT, and on fourth one perform the quirk.
Enabling Tx interrupts should change IIR value from IIR_NO_INT to
IIR_THRI which has been observed to stop the storm.
Fixes: e92fad024929 ("serial: 8250_dw: Add ACPI ID for Granite Rapids-D UART")
Cc: stable <stable@kernel.org>
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dw8250_handle_irq() takes port's lock multiple times with no good
reason to release it in between and calls serial8250_handle_irq()
that also takes port's lock.
Take port's lock only once in dw8250_handle_irq() and use
serial8250_handle_irq_locked() to avoid releasing port's lock in
between.
As IIR_NO_INT check in serial8250_handle_irq() was outside of port's
lock, it has to be done already in dw8250_handle_irq().
DW UART can, in addition to IIR_NO_INT, report BUSY_DETECT (0x7) which
collided with the IIR_NO_INT (0x1) check in serial8250_handle_irq()
(because & is used instead of ==) meaning that no other work is done by
serial8250_handle_irq() during an BUSY_DETECT interrupt.
This allows reorganizing code in dw8250_handle_irq() to do both
IIR_NO_INT and BUSY_DETECT handling right at the start simplifying
the logic.
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250_port exports serial8250_handle_irq() to HW specific 8250 drivers.
It takes port's lock within but a HW specific 8250 driver may want to
take port's lock itself, do something, and then call the generic
handler in 8250_port but to do that, the caller has to release port's
lock for no good reason.
Introduce serial8250_handle_irq_locked() which a HW specific driver can
call while already holding port's lock.
As this is new export, put it straight into a namespace (where all 8250
exports should eventually be moved).
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When DW UART is configured with BUSY flag, LCR writes may not always
succeed which can make any LCR write complex and very expensive.
Performing write directly can trigger IRQ and the driver has to perform
complex and distruptive sequence while retrying the write.
Therefore, it's better to avoid doing LCR write that would not change
the value of the LCR register. Add LCR write avoidance code into the
8250_dw driver's .serial_out() functions.
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250_dw driver needs to potentially perform very complex operations
during LCR writes because its BUSY handling prevents updates to LCR
while UART is BUSY (which is not fully under our control without those
complex operations). Thus, LCR writes should occur under port's lock.
Move LCR write under port's lock in serial8250_do_shutdown(). Also
split the LCR RMW so that the logic is on a separate line for clarity.
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is found in popular brands such as StarTech.com or Delock, and has
been a source of frustration to quite a few people, if I can trust
Amazon comments complaining about Linux support via the official
out-of-the-tree driver.
Signed-off-by: Martin Roukala (né Peres) <martin.roukala@mupuf.org>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260309-8250_pci_ax99100-v1-1-3328bdfd8e94@mupuf.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 039d4926379b ("serial: 8250: Toggle IER bits on only after irq
has been set up") moved IRQ setup before the THRE test, in combination
with commit 205d300aea75 ("serial: 8250: change lock order in
serial8250_do_startup()") the interrupt handler can run during the
test and race with its IIR reads. This can produce wrong THRE test
results and cause spurious registration of the
serial8250_backup_timeout timer. Unconditionally disable the IRQ for
the short duration of the test and re-enable it afterwards to avoid
the race.
Fixes: 039d4926379b ("serial: 8250: Toggle IER bits on only after irq has been set up")
Depends-on: 205d300aea75 ("serial: 8250: change lock order in serial8250_do_startup()")
Cc: stable <stable@kernel.org>
Signed-off-by: Peng Zhang <zhangpeng.00@bytedance.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Alban Bedel <alban.bedel@lht.dlh.de>
Tested-by: Maximilian Lueer <maximilian.lueer@lht.dlh.de>
Link: https://patch.msgid.link/20260224121639.579404-1-alban.bedel@lht.dlh.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
`dmaengine_terminate_async` does not guarantee that the
`__dma_tx_complete` callback will run. The callback is currently the
only place where `dma->tx_running` gets cleared. If the transaction is
canceled and the callback never runs, then `dma->tx_running` will never
get cleared and we will never schedule new TX DMA transactions again.
This change makes it so we clear `dma->tx_running` after we terminate
the DMA transaction. This is "safe" because `serial8250_tx_dma_flush`
is holding the UART port lock. The first thing the callback does is also
grab the UART port lock, so access to `dma->tx_running` is serialized.
Fixes: 9e512eaaf8f4 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Signed-off-by: Raul E Rangel <rrangel@google.com>
Link: https://patch.msgid.link/20260209135815.1.I16366ecb0f62f3c96fe3dd5763fcf6f3c2b4d8cd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the embedded platform, certain critical data, such as IMU data, is
transmitted through UART. The tty_flip_buffer_push() interface in the TTY
layer uses system_dfl_wq to handle the flipping of the TTY buffer.
Although the unbound workqueue can create new threads on demand and wake
up the kworker thread on an idle CPU, it may be preempted by real-time
tasks or other high-prio tasks.
flush_to_ldisc() needs to wake up the relevant data handle thread. When
executing __wake_up_common_lock(), it calls spin_lock_irqsave(), which
does not disable preemption but disables migration in RT-Linux. This
prevents the kworker thread from being migrated to other cores by CPU's
balancing logic, resulting in long delays. The call trace is as follows:
__wake_up_common_lock
__wake_up
ep_poll_callback
__wake_up_common
__wake_up_common_lock
__wake_up
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf
tty_port_default_receive_buf
flush_to_ldisc
In our system, the processing interval for each frame of IMU data
transmitted via UART can experience significant jitter due to this issue.
Instead of the expected 10 to 15 ms frame processing interval, we see
spikes up to 30 to 35 ms. Moreover, in just one or two hours, there can
be 2 to 3 occurrences of such high jitter, which is quite frequent. This
jitter exceeds the software's tolerable limit of 20 ms.
Introduce flip_wq in tty_port which can be set by tty_port_link_wq() or as
default linked to default workqueue allocated when tty_register_driver().
The default workqueue is allocated with flag WQ_SYSFS, so that cpumask and
nice can be set dynamically. The execution timing of tty_port_link_wq() is
not clearly restricted. The newly added function tty_port_link_driver_wq()
checks whether the flip_wq of the tty_port has already been assigned when
linking the default tty_driver's workqueue to the port. After the user has
set a custom workqueue for a certain tty_port using tty_port_link_wq(), the
system will only use this custom workqueue, even if tty_driver does not
have %TTY_DRIVER_NO_WORKQUEUE flag. When tty_port register device, flip_wq
link operation is done by tty_port_link_driver_wq(), but for in-memory
devices the link operation cannot cover all the cases. Although
tty_port_install() is dedicated for in-memory devices lik PTY to link port
allocated on demand, the logic of tty_port_install() is so simple that
people may not call it, vc_cons[0].d->port is one such case. We check the
buf.flip_wq when flip TTY buffer, if buf.flip_wq of TTY port is NULL, use
system_dfl_wq as a backup.
To avoid naming conflict of the default tty_driver's workqueue, using
'"%s-%s", driver->name, driver->driver_name' as the workqueue name. In
cases where driver_name is not specified and therefore is NULL, the
workqueue is not created. Drivers that do not define driver_name are
potentially in-memory devices like vty, which generally do not require
special workqueue settings. Even with the combination of name and
driver_name, the workqueue names can still be duplicated, as many tty
serial drivers use "ttyS" as dev_name and "serial" as driver_name. I
modified the conflicting driver_name of these drivers by appending a
suffix of _xx based on the corresponding .c file. If this modification is
not made, it could not only lead to duplicate workqueue names but also
result in duplicate entries for the /proc/tty/driver/<driver_name> nodes.
Introduce %TTY_DRIVER_NO_WORKQUEUE flag meaning not to create the
default single tty_driver workqueue. Two reasons why need to introduce the
%TTY_DRIVER_NO_WORKQUEUE flag:
1. If the WQ_SYSFS parameter is enabled, workqueue_sysfs_register() will
fail when trying to create a workqueue with the same name. The pty is an
example of this; if both CONFIG_LEGACY_PTYS and CONFIG_UNIX98_PTYS are
enabled, the call to tty_register_driver() in unix98_pty_init() will fail.
2. Different TTY ports may be used for different tasks, which may require
separate core binding control via workqueues. In this case, the workqueue
created by default in the TTY driver is unnecessary. Enabling this flag
prevents the creation of this redundant workqueue.
After applying this patch, we can set the related UART TTY flip buffer
workqueue by sysfs. We set the cpumask to CPU cores associated with the
IMU tasks, and set the nice to -20. Testing has shown significant
improvement in the previously described issue, with almost no stuttering
occurring anymore.
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Xin Zhao <jackzxcui1989@163.com>
Link: https://patch.msgid.link/20260213085039.3274704-1-jackzxcui1989@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the SystemBase Multi I/O serial cards, which are
"compatible" with a standard 16550A controllers, except that they need
to have their interrupts enabled in a proprietary way.
Tested with a Delock "Serial PCI Express x1 Card 8x Serial RS-232".
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20260225081739.946723-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial8250_release_dma() is NULL-aware, no need to check this in the caller.
While at it, make sure DMA won't be used again, by NULLifying the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260128142726.128175-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor
tweaks and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
Revert "tty: tty_port: add workqueue to flip TTY buffer"
tty: tty_port: add workqueue to flip TTY buffer
serial: 8250_pci: Remove custom deprecated baud setting routine
serial: 8250_omap: Remove custom deprecated baud setting routine
dt-bindings: serial: renesas,scif: Document RZ/G3L SoC
serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists
tty: hvc-iucv: Remove KMSG_COMPONENT macro
dt-bindings: serial: google,goldfish-tty: Convert to DT schema
dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum
serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done
serial: 8250: 8250_omap.c: Add support for handling UART error conditions
serial: SH_SCI: improve "DMA support" prompt
serial: Kconfig: fix ordering of entries for menu display
serial: 8250: fix ordering of entries for menu display
serial: imx: change SERIAL_IMX_CONSOLE to bool
8250_men_mcb: drop unneeded MODULE_ALIAS
serial: men_z135_uart: drop unneeded MODULE_ALIAS
dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs
serial: rsci: Convert to FIELD_MODIFY()
dt-bindings: serial: 8250: add SpacemiT K3 UART compatible
...
|
|
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In TI K3 SoCs, I/O daisy chaining is used to allow wakeup from UART when the
UART controller is off. Set UART device as wakeup capable using out-of-band
wakeup if the 'wakeup' pinctrl state exists and the device may wakeup.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260116-uart-wakeup-v2-1-0078ae9996e4@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fintek F81504/508/512 can support both RTS_ON_SEND and RTS_AFTER_SEND,
but pci_fintek_rs485_supported only announces the former.
This makes it impossible to unset SER_RS485_RTS_ON_SEND from
userspace because of uart_sanitize_serial_rs485(). Some devices
with these chips need RTS low on TX, so they are effectively broken.
Fix this by announcing the support for SER_RS485_RTS_AFTER_SEND,
similar to commit 068d35a7be65 ("serial: sc16is7xx: announce support
for SER_RS485_RTS_ON_SEND").
Fixes: 4afeced55baa ("serial: core: fix sanitizing check for RTS settings")
Cc: stable <stable@kernel.org>
Signed-off-by: Marnix Rijnart <marnix.rijnart@iwell.eu>
Link: https://patch.msgid.link/20260112000931.61703-1-marnix.rijnart@iwell.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
termination is done
Clear rx_running flag only after DMA teardown polling completes. In the
previous implementation the flag was being cleared while hardware teardown
was still in progress, creating a mismatch between software state
(flag = 0, "ready") and hardware state (still terminating).
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-3-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DMA IRQ handler does not accounts for the overrun(OE) or any other
errors being reported by the IP before triggering a DMA transaction which
leads to the interrupts not being handled resulting into an IRQ storm.
The way to handle OE is to:
1. Reset the RX FIFO.
2. Read the UART_RESUME register, which clears the internal flag
Earlier, the driver issued DMA transations even in case of OE which shouldn't
be done according to the OE handling mechanism mentioned above, as we are
resetting the FIFO's, refer section: "12.1.6.4.8.1.3.6 Overrun During
Receive" [0].
[0] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-2-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Improve the "8250/16550 serial support" menu so that entries in it
are displayed in a better order (reorder a few symbols) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 1f4ea4838b13 ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-3-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The devm_platform_get_and_ioremap_resource() function never returns
NULL, it returns error pointers. Fix the error checking to match.
Fixes: 25e95d763176 ("serial: 8250: Add Loongson uart driver support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aSsIa3KdAlXh5uQC@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify the probe() code by using dev_err_probe().
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-4-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add defines for better readability of the Indexed Control Register (ICR)
access. In enhanced mode SCR and LSR registers are used for ICR access.
The behavior of these register is different in this mode and that shall
be documented with dedicated defines.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Andy and Ilpo suggested to add missing includes, because the code shall
not rely on indirect includes. Add missing includes and remove one
include, which only enabled indirect includes.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-2-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Z125 define is not used anywhere, thus removed. Also used a
more specific name for the maximum number of ports per unit and
removed the duplicated define MAX_PORTS
Reviewed-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Signed-off-by: Filip Jensen <dev-Felipe.Jensen@duagon.com>
Link: https://patch.msgid.link/20251210164804.94801-2-dev-Felipe.Jensen@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move pm_runtime_set_active() call earlier in probe to simplify error
handling and add proper error checking to ensure the device is marked
as active before any runtime PM operations can occur.
Additionally, replace the const struct dev_pm_ops declaration with
_DEFINE_DEV_PM_OPS macro for better consistency with modern kernel PM
patterns.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-3-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add error checking for clk_prepare_enable() calls in
dw8250_runtime_resume(). Currently if either clock fails to enable,
the function returns success while leaving clocks in inconsistent state.
This change implements comprehensive error handling by checking the return
values of both clk_prepare_enable() calls. If the second clock enable
operation fails after the first clock has already been successfully
enabled, the code now properly cleans up by disabling and unpreparing
the first clock before returning. The error code is then propagated to
the caller, ensuring that clock enable failures are properly reported
rather than being silently ignored.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-2-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.19-rc1. Nothing
major at all, just small constant churn to make the tty layer
"cleaner" as well as serial driver updates and even a new test added!
Included in here are:
- More tty/serial cleanups from Jiri
- tty tiocsti test added to hopefully ensure we don't regress in this
area again
- sc16is7xx driver updates
- imx serial driver updates
- 8250 driver updates
- new hardware device ids added
- other minor serial/tty driver cleanups and tweaks
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
serial: sh-sci: Fix deadlock during RSCI FIFO overrun error
dt-bindings: serial: rsci: Drop "uart-has-rtscts: false"
LoongArch: dts: Add uart new compatible string
serial: 8250: Add Loongson uart driver support
dt-bindings: serial: 8250: Add Loongson uart compatible
serial: 8250: add driver for KEBA UART
serial: Keep rs485 settings for devices without firmware node
serial: qcom-geni: Enable Serial on SA8255p Qualcomm platforms
serial: qcom-geni: Enable PM runtime for serial driver
serial: sprd: Return -EPROBE_DEFER when uart clock is not ready
tty: serial: samsung: Declare earlycon for Exynos850
serial: icom: Convert PCIBIOS_* return codes to errnos
serial: 8250-of: Fix style issues in 8250_of.c
serial: add support of CPCI cards
serial: mux: Fix kernel doc for mux_poll()
tty: replace use of system_unbound_wq with system_dfl_wq
serial: 8250_platform: simplify IRQF_SHARED handling
serial: 8250: make share_irqs local to 8250_platform
serial: 8250: move skip_txen_test to core
serial: drop SERIAL_8250_DEPRECATED_OPTIONS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
|
|
Depmod fails for a kernel made with:
make allnoconfig
echo -e "CONFIG_MODULES=y\nCONFIG_SERIAL_8250=m\nCONFIG_SERIAL_8250_EXTENDED=y\nCONFIG_SERIAL_8250_RSA=y" >> .config
make olddefconfig
...due to a dependency loop:
depmod: ERROR: Cycle detected: 8250 -> 8250_base -> 8250
depmod: ERROR: Found 2 modules in dependency cycles!
This is caused by the move of 8250 RSA code from 8250_port.c (in
8250_base.ko) into 8250_rsa.c (in 8250.ko) by the commit 5a128fb475fb
("serial: 8250: move RSA functions to 8250_rsa.c"). The commit
b20d6576cdb3 ("serial: 8250: export RSA functions") tried to fix a
missing symbol issue with EXPORTs but those then cause this dependency
cycle.
Break dependency loop by moving 8250_rsa.o from 8250.ko to 8250_base.ko
and by passing univ8250_port_base_ops to univ8250_rsa_support() that
can make a local copy of it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Alex Davis <alex47794@gmail.com>
Fixes: 5a128fb475fb ("serial: 8250: move RSA functions to 8250_rsa.c")
Fixes: b20d6576cdb3 ("serial: 8250: export RSA functions")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/all/87frc3sd8d.fsf@posteo.net/
Link: https://lore.kernel.org/all/CADiockCvM6v+d+UoFZpJSMoLAdpy99_h-hJdzUsdfaWGn3W7-g@mail.gmail.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251110105043.4062-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the driver for on-chip UART used on Loongson family chips.
The hardware is similar to NS16550A, but there are the following
differences:
- Some chips (such as Loongson-2K2000) have added a fractional division
register to obtain the required baud rate accurately, so the
{get,set}_divisor callback is overridden.
- Due to hardware defects, quirk handling is required for
UART_MCR/UART_MSR.
Co-developed-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/2c2a01a276b9250efea0c7aa190efecdfd6fdf5a.1760166651.git.zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The KEBA UART is found in the system FPGA of KEBA PLC devices. It is
mostly 8250 compatible with extension for some UART modes.
3 different variants exist. The simpliest variant supports only RS-232
and is used for debug interfaces. The next variant supports only RS-485
and is used mostly for communication with KEBA panel devices. The third
variant is able to support RS-232, RS-485 and RS-422. For this variant
not only the mode of the UART is configured, also the physics and
transceivers are switched according to the mode.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Tested-by: Daniel Gierlinger <gida@keba.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch resolves the warning "sizeof *port should be sizeof(*port)"
detected by checkpatch.pl.
Signed-off-by: jempty.liang <imntjempty@163.com>
Link: https://patch.msgid.link/20251117034117.55588-1-imntjempty@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Addi-Data GmbH is manufacturing multi-serial ports cards supporting CompactPCI (known as CPCI).
Those cards are identified with different DeviceIds. Those cards integrating standard UARTs
work the same way as PCI/PCIe models already supported in the serial driver.
Signed-off-by: Magne Bruno <magne.bruno@addi-data.com>
Link: https://patch.msgid.link/20251110162456.341029-1-magne.bruno@addi-data.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
system_dfl_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251104105446.110884-1-marco.crivellari@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 2009, commit c82f63e411f1 ("PCI: check saved state before restore")
changed the behavior of pci_restore_state() such that it became necessary
to call pci_save_state() afterwards, lest recovery from subsequent PCI
errors fails.
The commit has just been reverted and so all the pci_save_state() after
pci_restore_state() calls that have accumulated in the tree are now
superfluous. Drop them.
Two drivers chose a different approach to achieve the same result:
drivers/scsi/ipr.c and drivers/net/ethernet/intel/e1000e/netdev.c set the
pci_dev's "state_saved" flag to true before calling pci_restore_state().
Drop this as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> # qat
Link: https://patch.msgid.link/c2b28cc4defa1b743cf1dedee23c455be98b397a.1760274044.git.lukas@wunner.de
|
|
IRQF_SHARED is the only flag handled in __serial8250_isa_init_ports()
and serial8250_probe_platform(). There is no need to precompute the
flags. Instead, initialize port->irqflags directly in the for loop.
Note the "if (bool)" is cheap and these are not hot paths anyway.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
share_irqs is used solely in 8250_platform. Make it local to that file.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250_core is the only place where skip_txen_test is used. And platform
and core end up in 8250.ko, so there is no change in module name (param
prefix). Therefore, move skip_txen_test there and make it local.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 3.7, 8250 was unintentionally renamed to 8250_core. This happened in
the commit 835d844d1a28 (8250_pnp: do pnp probe before legacy probe).
This made 8250.<xxxx> module options effectively defunct. Instead,
8250_core.<xxxx> worked.
In 3.9, the commit f2b8dfd9e480 (serial: 8250: Keep 8250.<xxxx> module
options functional after driver rename) made the original options work
again by introducing a hack.
Later in 3.9, the commit 9196d8acd7f9 (TTY: 8250, revert module name
change) changed the module name back to 8250 (from 8250_core). Since
then, the hack was there to support the transient 8250_core.<xxxx>
options. Those were present only in the 3.7..3.9 range.
These transient options were deprecated by 9326b047e4fd (TTY: 8250,
deprecated 8250_core.* options) in v3.9 too.
Now, after those 12 years, it is time to get rid of this hack
completely.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
