| Age | Commit message (Collapse) | Author | Lines |
|---|
|
TCPCI maxim driver directly writes to the charger's register space to
set charger mode depending on the power role. As MAX77759 chg driver
exists, this WAR is not required.
Instead, use a regulator interface to source vbus when typec is in
source power mode. In other power modes, this regulator will be turned
off if active.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260325-max77759-charger-v9-6-4486dd297adc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
FUSB302 fails to probe with -EINVAL if its interrupt line is connected via
an I2C GPIO expander, such as TI TCA6416.
Switch the interrupt handler to a threaded one, which also works behind
such GPIO expanders.
Cc: stable <stable@kernel.org>
Fixes: 309b6341d557 ("usb: typec: fusb302: Revert incorrect threaded irq fix")
Signed-off-by: Alexey Charkov <alchark@flipper.net>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogrerus@linux.intel.com>
Link: https://patch.msgid.link/20260317-fusb302-irq-v2-1-dbabd5c5c961@flipper.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Existing checks for VID/PID/DID in the driver are redundant since the
driver is already matched to the device via I2C device ID and OF
compatible strings, and they preclude the use of fallback compatibles.
Remove them to make the driver slimmer and adding new clones easier.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Alexey Charkov <alchark@flipper.net>
Link: https://patch.msgid.link/20260318-husb311-v4-4-69e029255430@flipper.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the chip indicates its "Connection Orientation" standard output control
in STANDARD_OUTPUT_CAPABILITIES register, it can do the thing by
programming CONFIG_STANDARD_OUTPUT register. Due to the optional feature,
the chip which not present this capability currently doesn't have a way to
correctly set the data path. This add the support to set orientation via
a simple GPIO.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260319-support-setting-orientation-use-gpio-v4-2-ab6dfa8610c2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support to enable TCPM to negotiate with
USB PD Standard Power Range Adjustable Voltage Supply (SPR AVS) when
acting as a power sink.
* Added support to the tcpm power supply properties, allowing userspace
to enable and control the dynamic limits (voltage and current)
specific to the SPR AVS contract.
* Implemented tcpm_pd_select_spr_avs_apdo() to select the appropriate
APDO and validate the requested voltage/current against both the
Source and Sink capabilities.
* Implemented tcpm_pd_build_spr_avs_request() to construct the
Request Data Object (RDO) for SPR AVS.
* Added SNK_NEGOTIATE_SPR_AVS_CAPABILITIES state to the state machine to
handle negotiation for SPR AVS.
* Updated the SNK_TRANSITION_SINK state to implement the SPR
AVS-specific VBUS transition rules, including reducing current draw to
PD_I_SNK_STBY_MA for large voltage changes, as required by USB PD spec.
Log stub captured when enabling AVS:
$ echo 3 > /sys/class/power_supply/tcpm-source-psy-1-0025/online
$ cat /d/usb/tcpm-1-0025/log
[ 358.895775] request to set AVS online
[ 358.895792] AMS POWER_NEGOTIATION start
[ 358.895806] state change SNK_READY -> AMS_START [rev3 POWER_NEGOTIATION]
[ 358.895850] state change AMS_START -> SNK_NEGOTIATE_SPR_AVS_CAPABILITIES [rev3 POWER_NEGOTIATION]
[ 358.895866] SPR AVS src_pdo_index:4 snk_pdo_index:2 req_op_curr_ma roundup:2200 req_out_volt_mv roundup:9000
[ 358.895880] Requesting APDO SPR AVS 4: 9000 mV, 2200 mA
[ 358.896405] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:0 pps_apdo_min_volt:0 ret:0
[ 358.896422] PD TX, header: 0x1a82
[ 358.900158] PD TX complete, status: 0
[ 358.900205] pending state change SNK_NEGOTIATE_SPR_AVS_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev3 POWER_NEGOTIATION]
[ 358.904832] PD RX, header: 0x1a3 [1]
[ 358.904854] state change SNK_NEGOTIATE_SPR_AVS_CAPABILITIES -> SNK_TRANSITION_SINK [rev3 POWER_NEGOTIATION]
[ 358.904888] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 700 ms [rev3 POWER_NEGOTIATION]
[ 359.021530] PD RX, header: 0x3a6 [1]
[ 359.021546] Setting voltage/current limit 9000 mV 2200 mA
[ 359.023035] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 pps_apdo_min_volt:0 ret:0
[ 359.023053] state change SNK_TRANSITION_SINK -> SNK_READY [rev3 POWER_NEGOTIATION]
[ 359.023090] AMS POWER_NEGOTIATION finished
$ cat /sys/class/power_supply/tcpm-source-psy-1-0025/online
3
Log stub captured when increasing voltage:
$ echo 9100000 > /sys/class/power_supply/tcpm-source-psy-1-0025/voltage_now
$ cat /d/usb/tcpm-1-0025/log
[ 632.116714] AMS POWER_NEGOTIATION start
[ 632.116728] state change SNK_READY -> AMS_START [rev3 POWER_NEGOTIATION]
[ 632.116779] state change AMS_START -> SNK_NEGOTIATE_SPR_AVS_CAPABILITIES [rev3 POWER_NEGOTIATION]
[ 632.116798] SPR AVS src_pdo_index:4 snk_pdo_index:2 req_op_curr_ma roundup:2200 req_out_volt_mv roundup:9100
[ 632.116811] Requesting APDO SPR AVS 4: 9100 mV, 2200 mA
[ 632.117315] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:0 pps_apdo_min_volt:0 ret:0
[ 632.117328] PD TX, header: 0x1c82
[ 632.121007] PD TX complete, status: 0
[ 632.121052] pending state change SNK_NEGOTIATE_SPR_AVS_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev3 POWER_NEGOTIATION]
[ 632.124572] PD RX, header: 0x5a3 [1]
[ 632.124594] state change SNK_NEGOTIATE_SPR_AVS_CAPABILITIES -> SNK_TRANSITION_SINK [rev3 POWER_NEGOTIATION]
[ 632.124623] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 700 ms [rev3 POWER_NEGOTIATION]
[ 632.149256] PD RX, header: 0x7a6 [1]
[ 632.149271] Setting voltage/current limit 9100 mV 2200 mA
[ 632.150770] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9100 pps_apdo_min_volt:0 ret:0
[ 632.150787] state change SNK_TRANSITION_SINK -> SNK_READY [rev3 POWER_NEGOTIATION]
[ 632.150823] AMS POWER_NEGOTIATION finished
$ cat /sys/class/power_supply/tcpm-source-psy-1-0025/voltage_now
9100000
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Amit Sunil Dhamne <amitsd@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260316150301.3892223-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in this branch as well to build on top of
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1366cd228b0c67b60a2c0c26ef37fe9f7cfedb7f.
The fwnode_usb_role_switch_get() returns NULL only if no connection is
found, returns ERR_PTR(-EPROBE_DEFER) if connection is found but deferred
probe is needed, or a valid pointer of usb_role_switch.
When switching from a NULL check to IS_ERR_OR_NULL(), usb_role_switch_get()
returns NULL and overwrites the ERR_PTR(-EPROBE_DEFER) returned by
fwnode_usb_role_switch_get(). This causes the deferred probe indication to
be lost, preventing the USB role switch from ever being retrieved.
Fixes: 1366cd228b0c ("tcpm: allow looking for role_sw device in the main node")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Tested-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260309074313.2809867-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for responding to Sink Cap Extended msg request. To achieve
this, include parsing support for DT properties related to Sink Cap
Extended. The request for Sink Cap Ext is a control message while the
response is an extended message (chunked). As the Sink Caps Extended
Data Block size (24 Byte) is less than MaxExtendedMsgChunkLen (26 Byte),
a single chunk is sufficient to complete this AMS.
Supporting sink cap extended messages while responding to a
Get_Sink_Caps_Extended request when port is in Sink role is required in
order to be compliant with at least USB PD Rev3.1 Ver1.8.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260223-skedb-v2-2-60675765bc7e@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move VID field to chip info to accommodate different VIDs.
Add chip info for Etek Micro ET7304. ET7304 is functionally
identical to the Richtek RT1715, with the only difference
being the VID.
Signed-off-by: Yuanshen Cao <alex.caoys@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260220-et7304-v3-2-ede2d9634957@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use a safer function strscpy() instead of strcpy() for copying to
arrays.
Only idiomatic code replacement, and no functional changes.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://patch.msgid.link/20260310094434.3639602-5-aichao@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
File-scope 'tcpci_pm_ops' is not used outside of this unit, so make it
static to silence sparse warning:
tcpm/tcpci.c:1002:1: warning: symbol 'tcpci_pm_ops' was not declared. Should it be static?
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://patch.msgid.link/20260216110403.159945-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support to use fusb302 based USB-C connectors with the DP altmode
helper code on devicetree based platforms. To get this working there
must be a DRM bridge chain from the DisplayPort controller to the USB-C
connector. E.g. on Rockchip RK3576:
root@rk3576 # cat /sys/kernel/debug/dri/0/encoder-0/bridges
bridge[0]: dw_dp_bridge_funcs
refcount: 7
type: [10] DP
OF: /soc/dp@27e40000:rockchip,rk3576-dp
ops: [0x47] detect edid hpd
bridge[1]: drm_aux_bridge_funcs
refcount: 4
type: [0] Unknown
OF: /soc/phy@2b010000:rockchip,rk3576-usbdp-phy
ops: [0x0]
bridge[2]: drm_aux_hpd_bridge_funcs
refcount: 5
type: [10] DP
OF: /soc/i2c@2ac50000/typec-portc@22/connector:usb-c-connector
ops: [0x4] hpd
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260310-fusb302-drm-dp-hpd-bridge-v1-1-ffd41ef9afe3@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplifies allocation and allows using __counted_by for extra runtime
analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20260306031639.46942-1-rosenp@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver updates for
7.0-rc1. Overall more lines were removed than added, thanks to
dropping the obsolete isp1362 USB host controller driver, always a
nice change.
Other than that, nothing major happening here, highlights are:
- lots of dwc3 driver updates and new hardware support added
- usb gadget function driver updates
- usb phy driver updates
- typec driver updates and additions
- USB rust binding updates for syntax and formatting changes
- more usb serial device ids added
- other smaller USB core and driver updates and additions
All of these have been in linux-next for a long time, with no reported
problems"
* tag 'usb-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (77 commits)
usb: typec: ucsi: Add Thunderbolt alternate mode support
usb: typec: hd3ss3220: Check if regulator needs to be switched
usb: phy: tegra: parametrize PORTSC1 register offset
usb: phy: tegra: parametrize HSIC PTS value
usb: phy: tegra: return error value from utmi_wait_register
usb: phy: tegra: cosmetic fixes
dt-bindings: usb: renesas,usbhs: Add RZ/G3E SoC support
usb: dwc2: fix resume failure if dr_mode is host
usb: cdns3: fix role switching during resume
usb: dwc3: gadget: Move vbus draw to workqueue context
USB: serial: option: add Telit FN920C04 RNDIS compositions
usb: dwc3: Log dwc3 address in traces
usb: gadget: tegra-xudc: Add handling for BLCG_COREPLL_PWRDN
usb: phy: tegra: add HSIC support
usb: phy: tegra: use phy type directly
usb: typec: ucsi: Enforce mode selection for cros_ec_ucsi
usb: typec: ucsi: Support mode selection to activate altmodes
usb: typec: Introduce mode_selection bit
usb: typec: Implement mode selection
usb: typec: Expose alternate mode priority via sysfs
...
|
|
Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also prevents force-threading of the primary handler and the
irq-core will warn about this.
Remove IRQF_ONESHOT from irqflags.
Fixes: 309b6341d5570 ("usb: typec: fusb302: Revert incorrect threaded irq fix")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260128095540.863589-12-bigeasy@linutronix.de
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ports are defined in the tcpc main node, fwnode_usb_role_switch_get()
returns an error, meaning usb_role_switch_get() (which would succeed)
never gets a chance to run as port->role_sw isn't NULL, causing a
regression on devices where this is the case.
Fix this by turning the NULL check into IS_ERR_OR_NULL(), so
usb_role_switch_get() can actually run and the device get properly probed.
Fixes: 2d8713f807a4 ("tcpm: switch check for role_sw device with fw_node")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Link: https://patch.msgid.link/20260105-fix-ppp-power-v2-1-6924f5a41224@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There should be a space between the two words: Responder and supports.
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://patch.msgid.link/20251229011624.146700-1-andyshrk@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB PD specification introduced new Adjustable Voltage Supply (AVS)
types for both Standard Power Range (SPR) and Extended Power Range (EPR)
sources.
Add definitions to correctly parse and handle the new AVS APDO. Use
bitfield macros to add inline helper functions to extract voltage,
current, power, and peak current fields to parse and log the details
of the new EPR AVS and SPR AVS APDO.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Kyle Tso <kyletso@google.com>
Reviewed-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20251015043017.3382908-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When there is no port entry in the tcpci entry itself, the driver will
trigger an error message "OF: graph: no port node found in /...../typec" .
It is documented that the dts node should contain an connector entry
with ports and several port pointing to devices with usb-role-switch
property set. Only when those connector entry is missing, it should
check for port entries in the main node.
We switch the search order for looking after ports, which will avoid the
failure message while there are explicit connector entries.
Fixes: d56de8c9a17d ("usb: typec: tcpm: try to get role switch from tcpc fwnode")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://patch.msgid.link/20251013-b4-ml-topic-tcpm-v2-1-63c9b2ab8a0b@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add wakeup support for tcpci. If the user enables the wakeup file, call
enable_irq_wake() during system suspend and disable_irq_wake() during
system resume. Since this driver supports shared interrupts, mask the
chip interrupt by default when wakeup is disabled to avoid affecting
other IRQ users.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250910105042.695146-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_handle_vdm_request delivers messages to the partner altmode or the
cable altmode depending on the SVDM response type, which is incorrect.
The partner or cable should be chosen based on the received message type
instead.
Also add this filter to ADEV_NOTIFY_USB_AND_QUEUE_VDM, which is used when
the Enter Mode command is responded to by a NAK on SOP or SOP' and when
the Exit Mode command is responded to by an ACK on SOP.
Fixes: 7e7877c55eb1 ("usb: typec: tcpm: add alt mode enter/exit/vdm support for sop'")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250821203759.1720841-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace devm_kzalloc() with devm_kcalloc() in qcom_pmic_typec_pdphy_probe()
and qcom_pmic_typec_port_probe() for safer memory allocation with built-in
overflow protection.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250819090125.540682-1-rongqianfeng@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fusb302 irq handler has been carefully optimized by Hans de Goede in
commit 207338ec5a27 ("usb: typec: fusb302: Improve suspend/resume
handling"). A recent 'fix' undid most of that work to avoid a virtio-gpio
driver bug.
This reverts the incorrect fix, since it is of very low quality. It
reverts the quirks from Hans change (and thus reintroduces the problems
fixed by Hans) while keeping the overhead from the original change.
The proper fix to support using fusb302 with an interrupt line provided
by virtio-gpio must be implemented in the virtio driver instead, which
should support disabling the IRQ from the fusb302 interrupt routine.
Cc: Hans de Goede <hansg@kernel.org>
Cc: Yongbo Zhang <giraffesnn123@gmail.com>
Fixes: 1c2d81bded19 ("usb: typec: fusb302: fix scheduling while atomic when using virtio-gpio")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250818-fusb302-unthreaded-irq-v1-1-3a9a11a9f56f@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
clean
Presently in `max_contaminant_is_contaminant()` if there's no
contaminant detected previously, CC is open & stopped toggling and no
contaminant is currently present, TCPC.RC would be programmed to do DRP
toggling. However, it didn't actively look for a connection. This would
lead to Type-C not detect *any* new connections. Hence, in the above
situation, re-enable toggling & program TCPC to look for a new
connection.
Also, return early if TCPC was looking for connection as this indicates
TCPC has neither detected a potential connection nor a change in
contaminant state.
In addition, once dry detection is complete (port is dry), restart
toggling.
Fixes: 02b332a06397e ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-2-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
comparator values
Low power mode is enabled when reading CC resistance as part of
`max_contaminant_read_resistance_kohm()` and left in that state.
However, it's supposed to work with 1uA current source. To read CC
comparator values current source is changed to 80uA. This causes a storm
of CC interrupts as it (falsely) detects a potential contaminant. To
prevent this, disable low power mode current sourcing before reading
comparator values.
Fixes: 02b332a06397 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Rule: add
Link: https://lore.kernel.org/stable/20250814-fix-upstream-contaminant-v1-1-801ce8089031%40google.com
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-1-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.
I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:
1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
(tcpm_set_pd_rx is enabled again, even though it is still on)
At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.
I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.
Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)
As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:
On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.
Fixes: c034a43e72dda ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver works fine with asynchronous probe.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-3-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The general recommendation is to not use of_match_ptr() or CONFIG_OF
ifdef.
Drop them.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-2-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver calls enable_irq_wake() during probe() unconditionally, and
never issues the required corresponding disable_irq_wake() to disable
hardware interrupt wakeup signals.
Additionally, whether or not a device should wake-up the system is
meant to be a policy decision based on sysfs (.../power/wakeup) in the
first place.
Update the driver to use the standard approach to enable/disable IRQ
wake during the suspend/resume callbacks. This solves both issues
described above.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-1-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well to build on top of for other
changes that depend on them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes Type-C compliance test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
tVbusON has a limit of 275ms when entering SRC_ATTACHED. Compliance
testers can interpret the TryWait.Src to Attached.Src transition after
Try.Snk as being in Attached.Src the entire time, so ~170ms is lost
to the debounce timer.
Setting the data role can be a costly operation in host mode, and when
completed after 100ms can cause Type-C compliance test check TD 4.7.5.V.4
to fail.
Turn VBUS on before tcpm_set_roles to meet timing requirement.
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618230606.3272497-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the gpio irqchip connected to a slow bus(e.g., i2c bus or virtio
bus), calling disable_irq_nosync() in top-half ISR handler will trigger
the following kernel BUG:
BUG: scheduling while atomic: RenderEngine/253/0x00010002
...
Call trace:
dump_backtrace+0x0/0x1c8
show_stack+0x1c/0x2c
dump_stack_lvl+0xdc/0x12c
dump_stack+0x1c/0x64
__schedule_bug+0x64/0x80
schedule_debug+0x98/0x118
__schedule+0x68/0x704
schedule+0xa0/0xe8
schedule_timeout+0x38/0x124
wait_for_common+0xa4/0x134
wait_for_completion+0x1c/0x2c
_virtio_gpio_req+0xf8/0x198
virtio_gpio_irq_bus_sync_unlock+0x94/0xf0
__irq_put_desc_unlock+0x50/0x54
disable_irq_nosync+0x64/0x94
fusb302_irq_intn+0x24/0x84
__handle_irq_event_percpu+0x84/0x278
handle_irq_event+0x64/0x14c
handle_level_irq+0x134/0x1d4
generic_handle_domain_irq+0x40/0x68
virtio_gpio_event_vq+0xb0/0x130
vring_interrupt+0x7c/0x90
vm_interrupt+0x88/0xd8
__handle_irq_event_percpu+0x84/0x278
handle_irq_event+0x64/0x14c
handle_fasteoi_irq+0x110/0x210
__handle_domain_irq+0x80/0xd0
gic_handle_irq+0x78/0x154
el0_irq_naked+0x60/0x6c
This patch replaces request_irq() with devm_request_threaded_irq() to
avoid the use of disable_irq_nosync().
Signed-off-by: Yongbo Zhang <giraffesnn123@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250526043433.673097-1-giraffesnn123@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.16-rc1.
Included in here are the following:
- USB offload support for audio devices.
I think this takes the record for the most number of patch series
(30+) over the longest period of time (2+ years) to get merged
properly.
Many props go to Wesley Cheng for seeing this effort through, they
took a major out-of-tree hacked-up-monstrosity that was created by
multiple vendors for their specific devices, got it all merged into
a semi-coherent set of changes, and got all of the different major
subsystems to agree on how this should be implemented both with
changes to their code as well as userspace apis, AND wrangled the
hardware companies into agreeing to go forward with this, despite
making them all redo work they had already done in their private
device trees.
This feature offers major power savings on embedded devices where a
USB audio stream can continue to flow while the rest of the system
is sleeping, something that devices running on battery power really
care about. There are still some more small tweaks left to be done
here, and those patches are still out for review and arguing among
the different hardware companies, but this is a major step forward
and a great example of how to do upstream development well.
- small number of thunderbolt fixes and updates, things seem to be
slowing down here (famous last words...)
- xhci refactors and reworking to try to handle some rough corner
cases in some hardware implementations where things don't always
work properly
- typec driver updates
- USB3 power management reworking and updates
- Removal of some old and orphaned UDC gadget drivers that had not
been used in a very long time, dropping over 11 thousand lines from
the tree, always a nice thing, making up for the 12k lines added
for the USB offload feature.
- lots of little updates and fixes in different drivers
All of these have been in linux-next for over 2 weeks, the USB offload
logic has been in there for 8 weeks now, with no reported issues"
* tag 'usb-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
ALSA: usb-audio: qcom: fix USB_XHCI dependency
ASoC: qdsp6: fix compile-testing without CONFIG_OF
usb: misc: onboard_usb_dev: fix build warning for CONFIG_USB_ONBOARD_DEV_USB5744=n
usb: typec: tipd: fix typo in TPS_STATUS_HIGH_VOLAGE_WARNING macro
USB: typec: fix const issue in typec_match()
USB: gadget: udc: fix const issue in gadget_match_driver()
USB: gadget: fix up const issue with struct usb_function_instance
USB: serial: pl2303: add new chip PL2303GC-Q20 and PL2303GT-2AB
USB: serial: bus: fix const issue in usb_serial_device_match()
usb: usbtmc: Fix timeout value in get_stb
usb: usbtmc: Fix read_stb function and get_stb ioctl
ALSA: qc_audio_offload: try to reduce address space confusion
ALSA: qc_audio_offload: avoid leaking xfer_buf allocation
ALSA: qc_audio_offload: rename dma/iova/va/cpu/phys variables
ALSA: usb-audio: qcom: Fix an error handling path in qc_usb_audio_probe()
usb: misc: onboard_usb_dev: Fix usb5744 initialization sequence
dt-bindings: usb: ti,usb8041: Add binding for TI USB8044 hub controller
usb: misc: onboard_usb_dev: Add support for TI TUSB8044 hub
usb: gadget: lpc32xx_udc: Use USB API functions rather than constants
usb: gadget: epautoconf: Use USB API functions rather than constants
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"LED Triggers:
- Allow writing "default" to the sysfs 'trigger' attribute to set an
LED to its default trigger
- If the default trigger is "none", writing "default" will remove the
current trigger
- Updated sysfs ABI documentation for the new "default" trigger
functionality
LED KUnit Testing:
- Provide a skeleton KUnit test suite for the LEDs framework
- Expand the LED class device registration KUnit test to cover more
scenarios, including 'brightness_get' behavior
- Add KUnit tests for the LED lookup and get API ('led_add_lookup',
'devm_led_get')
LED Flash Class:
- Add support for setting flash/strobe duration through a new
'duration_set' op and 'led_set_flash_duration()' function, aligning
with 'V4L2_CID_FLASH_DURATION'
Texas Instruments TPS6131x:
- Add a new driver for the TPS61310/TPS61311 flash LED controllers
- The driver supports the device's three constant-current sinks for
flash and torch modes
LED Core:
- Prevent potential 'snprintf()' truncations in LED names by checking
for buffer overflows
ChromeOS EC LEDs:
- Avoid a -Wflex-array-member-not-at-end GCC warning by replacing an
on-stack flexible structure definition with a utility function call
Multicolor LEDs:
- Fix issue where setting multi_intensity while software blinking is
active could stop blinking
PCA955x LEDs:
- Avoid potential buffer overflow when creating default labels by
changing a field's type to 'u8' and updating format specifiers
PCA995x LEDs:
- Fix a typo (stray space) in an 'of_device_id' entry in the
'pca995x_of_match' table
Kconfig:
- Prevent LED drivers from being enabled by default when
'COMPILE_TEST' is set
Device Property API:
- Split 'device_get_child_node_count()' into a new helper
'fwnode_get_child_node_count()' that doesn't require a device
struct, making the API more symmetrical
Driver Modernization (using 'fwnode_get_child_node_count()'):
- Update 'leds-pwm-multicolor', 'leds-ncp5623' and 'leds-ncp5623' to
use the new 'fwnode_get_child_node_count()' helper, removing their
custom implementation
- As above in the USB Type-C TCPM driver
Driver Modernization (using new GPIO setter callbacks):
- Convert 'leds-lgm-sso' to use new GPIO line value setter callbacks
which return an integer for error handling
- Convert 'leds-pca955x', 'leds-pca9532' and 'leds-tca6507' to use
new GPIO setter callbacks
Documentation:
- Remove the '.rst' extension for 'leds-st1202' in the documentation
index for consistency
LP8860 LEDs:
- Use 'regmap_multi_reg_write()' for EEPROM writes instead of manual
looping
- Use scoped mutex guards and 'devm_mutex_init()' to simplify
function exits and ensure automatic cleanup
- Remove default register definitions that are unused when regmap
caching is not active
- Use 'devm_regulator_get_enable_optional()' to handle the optional
regulator, simplifying enabling and removing manual disabling
- Refactor 'lp8860_unlock_eeprom()' to only perform the unlock
operation, removing the lock part and an unnecessary parameter
- Use a 'devm' action to disable the enable-GPIO, simplifying cleanup
and error paths, and remove the now-empty '.remove()' function
Turris Omnia LEDs:
- Drop unnecessary commas in terminator entries of 'struct attribute'
and 'struct of_device_id' arrays
MT6370 RGB LEDs:
- Use the 'LINEAR_RANGE()' for defining 'struct linear_range' entries
to improve robustness
Texas Instruments TPS6131x:
- Add new devicetree bindings for the TI TPS61310/TPS61311 flash LED
driver"
* tag 'leds-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (31 commits)
leds: tps6131x: Add support for Texas Instruments TPS6131X flash LED driver
dt-bindings: leds: Add Texas Instruments TPS6131x flash LED driver
leds: flash: Add support for flash/strobe duration
leds: rgb: leds-mt6370-rgb: Improve definition of some struct linear_range
leds: led-test: Provide tests for the lookup and get infrastructure
leds: led-test: Fill out the registration test to cover more test cases
leds: led-test: Remove standard error checking after KUNIT_ASSERT_*()
leds: pca995x: Fix typo in pca995x_of_match's of_device_id entry
leds: Provide skeleton KUnit testing for the LEDs framework
leds: tca6507: Use new GPIO line value setter callbacks
leds: pca9532: Use new GPIO line value setter callbacks
leds: pca955x: Use new GPIO line value setter callbacks
leds: lgm-sso: Use new GPIO line value setter callbacks
leds: Do not enable by default during compile testing
leds: turris-omnia: Drop commas in the terminator entries
leds: lp8860: Disable GPIO with devm action
leds: lp8860: Only unlock in lp8860_unlock_eeprom()
leds: lp8860: Enable regulator using enable_optional helper
leds: lp8860: Remove default regs when not caching
leds: lp8860: Use new mutex guards to cleanup function exits
...
|
|
Initialize negotiated_rev and negotiated_rev_prime based on the port's
configured PD revision (rev_major) rather than always defaulting to
PD_MAX_REV. This ensures ports start PD communication using their
appropriate revision level.
This allows proper communication with devices that require specific
PD revision levels, especially for the hardware designed for PD 1.0
or 2.0 specifications.
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250513130834.1612602-1-chou.cosmo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A state check was previously added to tcpm_queue_vdm_unlocked to
prevent a deadlock where the DisplayPort Alt Mode driver would be
executing work and attempting to grab the tcpm_lock while the TCPM
was holding the lock and attempting to unregister the altmode, blocking
on the altmode driver's cancel_work_sync call.
Because the state check isn't protected, there is a small window
where the Alt Mode driver could determine that the TCPM is
in a ready state and attempt to grab the lock while the
TCPM grabs the lock and changes the TCPM state to one that
causes the deadlock. The callstack is provided below:
[110121.667392][ C7] Call trace:
[110121.667396][ C7] __switch_to+0x174/0x338
[110121.667406][ C7] __schedule+0x608/0x9f0
[110121.667414][ C7] schedule+0x7c/0xe8
[110121.667423][ C7] kernfs_drain+0xb0/0x114
[110121.667431][ C7] __kernfs_remove+0x16c/0x20c
[110121.667436][ C7] kernfs_remove_by_name_ns+0x74/0xe8
[110121.667442][ C7] sysfs_remove_group+0x84/0xe8
[110121.667450][ C7] sysfs_remove_groups+0x34/0x58
[110121.667458][ C7] device_remove_groups+0x10/0x20
[110121.667464][ C7] device_release_driver_internal+0x164/0x2e4
[110121.667475][ C7] device_release_driver+0x18/0x28
[110121.667484][ C7] bus_remove_device+0xec/0x118
[110121.667491][ C7] device_del+0x1e8/0x4ac
[110121.667498][ C7] device_unregister+0x18/0x38
[110121.667504][ C7] typec_unregister_altmode+0x30/0x44
[110121.667515][ C7] tcpm_reset_port+0xac/0x370
[110121.667523][ C7] tcpm_snk_detach+0x84/0xb8
[110121.667529][ C7] run_state_machine+0x4c0/0x1b68
[110121.667536][ C7] tcpm_state_machine_work+0x94/0xe4
[110121.667544][ C7] kthread_worker_fn+0x10c/0x244
[110121.667552][ C7] kthread+0x104/0x1d4
[110121.667557][ C7] ret_from_fork+0x10/0x20
[110121.667689][ C7] Workqueue: events dp_altmode_work
[110121.667697][ C7] Call trace:
[110121.667701][ C7] __switch_to+0x174/0x338
[110121.667710][ C7] __schedule+0x608/0x9f0
[110121.667717][ C7] schedule+0x7c/0xe8
[110121.667725][ C7] schedule_preempt_disabled+0x24/0x40
[110121.667733][ C7] __mutex_lock+0x408/0xdac
[110121.667741][ C7] __mutex_lock_slowpath+0x14/0x24
[110121.667748][ C7] mutex_lock+0x40/0xec
[110121.667757][ C7] tcpm_altmode_enter+0x78/0xb4
[110121.667764][ C7] typec_altmode_enter+0xdc/0x10c
[110121.667769][ C7] dp_altmode_work+0x68/0x164
[110121.667775][ C7] process_one_work+0x1e4/0x43c
[110121.667783][ C7] worker_thread+0x25c/0x430
[110121.667789][ C7] kthread+0x104/0x1d4
[110121.667794][ C7] ret_from_fork+0x10/0x20
Change tcpm_queue_vdm_unlocked to queue for tcpm_queue_vdm_work,
which can perform the state check while holding the TCPM lock
while the Alt Mode lock is no longer held. This requires a new
struct to hold the vdm data, altmode_vdm_event.
Fixes: cdc9946ea637 ("usb: typec: tcpm: enforce ready state when queueing alt mode vdm")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250506232853.1968304-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Register read of TCPC_RX_BYTE_CNT returns the total size consisting of:
PD message (pending read) size + 1 Byte for Frame Type (SOP*)
This is validated against the max PD message (`struct pd_message`) size
without accounting for the extra byte for the frame type. Note that the
struct pd_message does not contain a field for the frame_type. This
results in false negatives when the "PD message (pending read)" is equal
to the max PD message size.
Fixes: 6f413b559f86 ("usb: typec: tcpci_maxim: Chip level TCPC driver")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/stable/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d%40google.com
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b2c ("staging: typec: tcpm: Check for Rp for tPDDebounce")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tcpci chip vbus pin is possibly driven by an regulator. This patch
is adding support to enable an optional vdd regulator before probing.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpci-v1-1-4442c7d0ee1e@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The funciton tcpm_acc_attach is not setting the proper state when
calling tcpm_set_role. The function tcpm_set_role is currently only
handling TYPEC_STATE_USB. For the tcpm_acc_attach to switch into other
modal states tcpm_set_role needs to be extended by an extra state
parameter. This patch is handling the proper state change when calling
tcpm_acc_attach.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-3-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch extends the is_debug macro to cover the sink case (ufp). It
also handles the transition to access the DEBUG_ACC_ATTACHED state in
the sink case. It also handles the debounce case in which the cc
pins are not immediately valid after the plug event.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-2-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the function tcpm_acc_attach is not setting the data and role for
for the sink case we extend it to check for it first.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-1-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
