| Age | Commit message (Collapse) | Author | Lines |
|---|
|
phy common properties
Vladimir Oltean <vladimir.oltean@nxp.com> wrote:
Introduce "rx-polarity" and "tx-polarity" device tree properties with
Kunit tests
|
|
Differential signaling is a technique for high-speed protocols to be
more resilient to noise. At the transmit side we have a positive and a
negative signal which are mirror images of each other. At the receiver,
if we subtract the negative signal (say of amplitude -A) from the
positive signal (say +A), we recover the original single-ended signal at
twice its original amplitude. But any noise, like one coming from EMI
from outside sources, is supposed to have an almost equal impact upon
the positive (A + E, E being for "error") and negative signal (-A + E).
So (A + E) - (-A + E) eliminates this noise, and this is what makes
differential signaling useful.
Except that in order to work, there must be strict requirements observed
during PCB design and layout, like the signal traces needing to have the
same length and be physically close to each other, and many others.
Sometimes it is not easy to fulfill all these requirements, a simple
case to understand is when on chip A's pins, the positive pin is on the
left and the negative is on the right, but on the chip B's pins (with
which A tries to communicate), positive is on the right and negative on
the left. The signals would need to cross, using vias and other ugly
stuff that affects signal integrity (introduces impedance
discontinuities which cause reflections, etc).
So sometimes, board designers intentionally connect differential lanes
the wrong way, and expect somebody else to invert that signal to recover
useful data. This is where RX and TX polarity inversion comes in as a
generic concept that applies to any high-speed serial protocol as long
as it uses differential signaling.
I've stopped two attempts to introduce more vendor-specific descriptions
of this only in the past month:
https://lore.kernel.org/linux-phy/20251110110536.2596490-1-horatiu.vultur@microchip.com/
https://lore.kernel.org/netdev/20251028000959.3kiac5kwo5pcl4ft@skbuf/
and in the kernel we already have merged:
- "st,px_rx_pol_inv"
- "st,pcie-tx-pol-inv"
- "st,sata-tx-pol-inv"
- "mediatek,pnswap"
- "airoha,pnswap-rx"
- "airoha,pnswap-tx"
and maybe more. So it is pretty general.
One additional element of complexity is introduced by the fact that for
some protocols, receivers can automatically detect and correct for an
inverted lane polarity (example: the PCIe LTSSM does this in the
Polling.Configuration state; the USB 3.1 Link Layer Test Specification
says that the detection and correction of the lane polarity inversion in
SuperSpeed operation shall be enabled in Polling.RxEQ.). Whereas for
other protocols (SGMII, SATA, 10GBase-R, etc etc), the polarity is all
manual and there is no detection mechanism mandated by their respective
standards.
So why would one even describe rx-polarity and tx-polarity for protocols
like PCIe, if it had to always be PHY_POL_AUTO?
Related question: why would we define the polarity as an array per
protocol? Isn't the physical PCB layout protocol-agnostic, and aren't we
describing the same physical reality from the lens of different protocols?
The answer to both questions is because multi-protocol PHYs exist
(supporting e.g. USB2 and USB3, or SATA and PCIe, or PCIe and Ethernet
over the same lane), one would need to manually set the polarity for
SATA/Ethernet, while leaving it at auto for PCIe/USB 3.0+.
I also investigated from another angle: what if polarity inversion in
the PHY is one layer, and then the PCIe/USB3 LTSSM polarity detection is
another layer on top? Then rx-polarity = <PHY_POL_AUTO> doesn't make
sense, it can still be rx-polarity = <PHY_POL_NORMAL> or <PHY_POL_INVERT>,
and the link training state machine figures things out on top of that.
This would radically simplify the design, as the elimination of
PHY_POL_AUTO inherently means that the need for a property array per
protocol also goes away.
I don't know how things are in the general case, but at least in the 10G
and 28G Lynx SerDes blocks from NXP Layerscape devices, this isn't the
case, and there's only a single level of RX polarity inversion: in the
SerDes lane. In the case of PCIe, the controller is in charge of driving
the RDAT_INV bit autonomously, and it is read-only to software.
So the existence of this kind of SerDes lane proves the need for
PHY_POL_AUTO to be a third state.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260111093940.975359-5-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
XAUI (eXtended Attachment Unit Interface) is a high-speed serial interface
standard for 10 Gigabit Ethernet (10GbE). It uses four lanes with each
lane operating at 3.125 Gbps (totaling 10 Gbps), to extend the XGMII
interface across circuit boards, commonly used in backplanes for
networking switches and high-performance computing. XAUI is defined as a
standardized instantiation of XGMII Extender in the IEEE 802.3
specification.
Add definition for XAUI PHY type.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
[s-vadapalli: added detailed description of XAUI in the commit message]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260112054636.108027-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
SM8[456]50 SoCs
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock named
"PHY_AUX_CLK" which is an input of the Global Clock Controller (GCC) which
is muxed & gated then returned to the PHY as an input.
Document the clock IDs to select the PIPE clock or the AUX clock,
also enforce a second clock-output-names and a #clock-cells value of 1
for the PCIe Gen4x2 PHY found in the SM8[456]50 SoCs.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-1-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current QMP USB3-DP PHY bindings are based on the original MSM8996
binding which provided multiple PHYs per IP block and these in turn were
described by child nodes.
The QMP USB3-DP PHY block provides a single multi-protocol PHY and even
if some resources are only used by either the USB or DP part of the
device there is no real benefit in describing these resources in child
nodes.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers (e.g. does not include the PCS LANE
registers).
This is specifically true for later USB4-USB3-DP QMP PHYs where the TX
registers are used by both the USB3 and DP parts of the PHY (and where
the USB4 part of the PHY was not covered by the binding at all). Notably
there are also no DP "RX" (sic) registers as described by the current
bindings and the DP "PCS" region is really a set of DP_PHY registers.
Add a new binding for the USB4-USB3-DP QMP PHYs found on SC8280XP which
further bindings can be based on.
Note that the binding uses a PHY index to access either the USB3 or DP
part of the PHY and that this can later be used also for the USB4 part
if needed.
Similarly, the clock inputs and outputs can later be extended to support
USB4.
Also note that the current binding is simply removed instead of being
deprecated as it was only recently merged and would not allow for
supporting DP mode.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221121085058.31213-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add definition for USXGMII phy type.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220628122255.24265-3-rogerq@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add clock ID for Sierra derived reference clock.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211223060137.9252-15-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Rename SSC macros to use generic names instead of PHY specific names,
so that they can be used to specify SSC modes for both Torrent and
Sierra. Renaming the macros should not affect the things as these are
not being used in any DTS file yet.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211223060137.9252-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add binding for reference clock PAD modes of the i.MX8 PCIe PHY.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1638432158-4119-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Lan966x has: 2 integrated PHYs, 3 SerDes and 2 RGMII interfaces. Which
requires to be muxed based on the HW representation.
So add constants for each interface to be able to distinguish them.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20211116100818.1615762-3-horatiu.vultur@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add clock IDs for derived and received reference clock output.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210922123735.21927-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Document a new phy-type property which will be used to determine whether
the phy should operate in D-PHY or C-PHY mode.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210617144349.28448-3-jonathan@marek.ca
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
provider
Add #clock-cells binding to model Sierra as clock provider and include
clock IDs for PLL_CMNLC and PLL_CMNLC1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210319124128.13308-12-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
No functional change. In order to have a single header file for all
Cadence SERDES move phy-cadence-torrent.h to phy-cadence.h. This is
in preparation for adding Cadence Sierra SERDES specific macros.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210319124128.13308-9-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add binding for refclk driver used to route the refclk out of torrent
SERDES.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210310112745.3445-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add bindings for AM64 SERDES Wrapper.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210310112745.3445-2-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add definition for QSGMII phy type.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1600327846-9733-5-git-send-email-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add binding to specify Spread Spectrum Clocking mode used.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1600280911-9214-7-git-send-email-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add DT bindings for the Xilinx ZynqMP PHY. ZynqMP SoCs have a High Speed
Processing System Gigabit Transceiver which provides PHY capabilities to
USB, SATA, PCIE, Display Port and Ehernet SGMII controllers.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200629120054.29338-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add definition for Ethernet PCS phy type.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/6091f0d2a1046f1e3656d9e33b6cc433d5465eaf.1589868358.git.eswara.kota@linux.intel.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add definition for DisplayPort phy type.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add the bindings for the PCIe PHY on Lantiq VRX200 and ARX300 SoCs.
The IP block contains settings for the PHY and a PLL.
The PLL mode is configurable through a dedicated #phy-cell in .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AM654x has two SERDES instances. Each instance has three input clocks
(left input, externel reference clock and right input) and two output
clocks (left output and right output) in addition to a PLL mux clock
which the SERDES uses for Clock Multiplier Unit (CMU refclock).
The PLL mux clock can select from one of the three input clocks.
The right output can select between left input and external reference
clock while the left output can select between the right input and
external reference clock.
The left and right input reference clock of SERDES0 and SERDES1
respectively are connected to the SoC clock. In the case of two lane
SERDES personality card, the left input of SERDES1 is connected to
the right output of SERDES0 in a chained fashion.
See section "Reference Clock Distribution" of AM65x Sitara Processors
TRM (SPRUID7 – April 2018) for more details.
Add dt-binding documentation in order to represent all these different
configurations in device tree.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
SERDES_MAX is a valid value to index ctrl->phys in
drivers/phy/mscc/phy-ocelot-serdes.c. But, currently,
there is an out-of-bounds bug in the mentioned driver
when reading from ctrl->phys, because the size of
array ctrl->phys is SERDES_MAX.
Partially fix this by updating SERDES_MAX to be SERDES6G_MAX + 1.
Notice that this is the first part of the solution to
the out-of-bounds bug mentioned above. Although this
change is not dependent on any other one.
Suggested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Microsemi Ocelot has multiple SerDes and requires that the SerDes be
muxed accordingly to the hardware representation.
Let's add a constant for each SerDes available in the Microsemi Ocelot.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To improve eye diagram for PHYs on different boards of same SOC,
some parameters may need to be changed. Provide device tree
properties to override these from board specific device tree
files. While at it, replace "qcom,qusb2-v2-phy" with compatible
string for USB2 PHY on sdm845 which was earlier added for
sdm845 only.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add definition for UFS phy type.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add a binding document for the USB2.0 PHY found on the IMG Pistachio SoC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Now there are generic phy type constants declared in phy.h, migrate over to
using them rather than defining our own. This change has been done as one
atomic commit to be bisectable.
Note: The values of the defines are the same, so there is no ABI breakage
with this patch.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The Armada 375 SoC comes with an USB2 host and device controller and
an USB3 controller. The USB cluster control register allows to manage
common features of both USB controllers.
This commit adds a driver integrated in the generic PHY framework to
control this USB cluster feature.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[ kishon@ti.com : Made it to use the updated devm_phy_create API and
soem cosmentic changes in Kconfig file.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
|
|
This provides the shared header file which will be reference from both
PHY driver and its associated Device Tree node(s).
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
|
|
This provides the shared header file which will be reference from both
the MiPHY365x driver and its associated Device Tree node(s).
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
